With the rapid development of social economy, the use of membrane structure parking sheds is also increasing. Light transmittance is one of the widely recognized characteristics of modern membrane structure parking sheds. The light transmittance of membrane materials can provide the required illumination for buildings, which is very important for building energy conservation. Now let's learn about the construction and precautions for parking sheds in Jinan.

A、加工準備及下料：依據施工圖放樣，放樣和號料時要預留焊接收縮量和加工余量，依據放樣作樣板。

A. Processing preparation and blanking: Set out according to the construction drawing, reserve welding shrinkage and machining allowance during setting out and marking, and use the setting out as a template.

B、預埋件安裝處理：定位預埋件安裝位置，打鉆安裝。要求預埋件位置準確、埋設牢固。標高偏差不大于9mm，左右位移不大于20mm。

B. Installation treatment of embedded parts: locate the installation position of embedded parts, and drill for installation. The embedded parts shall be accurately positioned and firmly embedded. The elevation deviation shall not be greater than 9mm, and the left and right displacement shall not be greater than 20mm.

C、測量放線：依據土建標高基準線測預埋件標高線，檢查預埋件標高偏差、左右偏差。整理結果，確定預埋件分隔的調整處理方案。

C. Surveying and setting out: measure the elevation center line of embedded parts according to the civil engineering elevation reference line, and check the elevation deviation and left and right deviation of embedded parts. Organize the results and determine the adjustment and treatment plan for the separation of embedded parts.

D、懸掛臂安裝焊接：懸掛臂安裝采用焊接，需檢查焊接節，調節懸掛臂設計坡度，準確無誤方能進行焊接。靠邊一條懸掛臂準確無誤后，安裝另一邊一條懸掛臂，就位準確后點焊。

D. Suspension arm installation and welding: The suspension arm installation adopts welding, and it is necessary to check the welding joints, adjust the design slope of the suspension arm, and conduct welding only if it is accurate and correct. After the suspension arm on the side is accurate, install the other suspension arm, and conduct spot welding after it is correctly positioned.

停車棚在施工時的步驟：

Steps for construction of parking sheds:

一，加工準備及下料：依據施工圖放樣，放樣和號料時要預留焊接收縮量和加工余量，依據放樣作樣板。

1、 Processing preparation and blanking: Set out according to the construction drawing, reserve welding shrinkage and machining allowance during setting out and blanking, and use the setting out as a template.

二，預埋件安裝處理：定位預埋件安裝位置，打鉆安裝。要求預埋件位置準確、埋設牢固。標高偏差不大于9mm，左右位移不大于20mm。

2、 Installation and processing of embedded parts: locate the installation position of the embedded parts and drill for installation. The embedded parts shall be accurately positioned and firmly embedded. The elevation deviation shall not be greater than 9mm, and the left and right displacement shall not be greater than 20mm.

三，測量放線：依據土建標高基準線測預埋件標高線，檢查預埋件標高偏差、左右偏差。整理結果，確定預埋件分隔的調整處理方案。

3、 Surveying and setting out: measure the elevation center line of embedded parts according to the civil engineering elevation reference line, and check the elevation deviation and left and right deviation of embedded parts. Organize the results and determine the adjustment and treatment plan for the separation of embedded parts.

四，懸掛臂安裝焊接：懸掛臂安裝采用焊接，需檢查焊接節，調節懸掛臂設計坡度，準確無誤方能進行焊接。靠邊一條懸掛臂準確無誤后，安裝另一邊一條懸掛臂，就位準確后點焊。

4、 Suspension arm installation and welding: Suspension arm installation adopts welding. It is necessary to inspect the welding joints, adjust the design slope of the suspension arm, and conduct welding only if it is accurate and correct. After the suspension arm on the side is accurate, install the other suspension arm, and conduct spot welding after it is correctly positioned.

通過以上小編的詳細介紹，我們對以上的信息有所了解，希望以上有您需要的信息，需要幫助的可以及時聯系我們。更多事項就來咨詢我們http://www.xilizx.com吧！

Through the detailed introduction by the above editor, we have gained some understanding of the above information. We hope that you have the information you need above. If you need help, please feel free to contact us in a timely manner. For more information, please consult us http://www.xilizx.com Come on!