在戶外進行遮陽蓬安裝可是一項大活動，僅僅靠一個人是完成不了的，但是同時幾人進行遮陽蓬安裝往往會出現不協調的紕漏，這時候需要我們業余人員多多了解怎樣正確的將濟南遮陽蓬安裝完成，了解遮陽蓬安裝的6個必備知識。

Installing the awning outdoors is a big activity, which can't be completed by only one person. However, at the same time, several people often make uncoordinated mistakes when installing the awning. At this time, we need more amateur staff to understand how to correctly install the awning in Jinan, and understand the six necessary knowledge of awning installation.

1、戶外遮陽篷安裝條件確定：混凝土、磚墻、鋼結構、木質、空心墻或需另做機構。

1. The installation conditions of outdoor awning are determined as follows: concrete, brick wall, steel structure, wood, hollow wall or other structures need to be made.

2、戶外遮陽篷安裝方式確定：貼墻式、吊頂式、斜吊式或其它特殊情況另做機構。

2. The installation method of outdoor sunshade shall be determined as follows: wall-attached, ceiling, inclined or other special cases.

3、戶外遮陽篷的掛靠方式：分為嵌入式和外掛式

3. The hanging method of outdoor awning: it is divided into embedded type and external type

4、戶外遮陽篷操縱方向的確認：人始終面對遮陽篷為基準。

4. Confirmation of operation direction of outdoor awning: people always face the awning as the benchmark.

5、戶外遮陽篷預留電機接線位

5. Reserved motor wiring position for outdoor awning

6、充分考慮遮陽篷日后的保養與維護，將它設計在合理位置。

6. Give full consideration to the future maintenance of the awning, and design it in a reasonable position.

遮陽篷的安裝步驟及注意事項如下：

The installation steps and precautions of the sunshade are as follows:

1、骨架桁條表面必須平整，不能有毛刺、焊疤等;如果發現這些問題一定要打磨平整以后再安裝，否則會劃傷表面UV涂層，導致老化的加快。

1. The surface of the framework stringer must be flat and free of burrs, welding scars, etc; If these problems are found, they must be polished and leveled before installation, otherwise the UV coating on the surface will be scratched, resulting in accelerated aging.

2、骨架上的油漆、涂料須干燥，不得殘留揮發性溶劑;由于耐酸堿性較弱，必須在揮發完畢后再安裝。

2. The paint and coating on the framework must be dry without residual volatile solvent; Due to weak acid and alkali resistance, it must be installed after volatilization.

3、把EPDM膠條鋪設并粘貼于骨架上;這樣可加固與骨架的貼切度，增加承重能力。

3. Lay and paste EPDM adhesive strips on the framework; This can strengthen the fit with the skeleton and increase the bearing capacity.

4、檢測骨架上椽子間的中心距離及檁條間的中心距離，須符合設計要求;如跨距過大，會影響遮陽篷的性。

4. The center distance between rafters on the framework and between purlins shall be tested to meet the design requirements; If the span is too large, the safety of the awning will be affected.

5、用專用封口膠帶封閉板材端孔后鋪設板材;板材之間用H條連接，再接口處打上專用封口膠，可以有效的防止遮陽篷漏水。

5. Use special sealing tape to seal the plate end hole and lay the plate; The plates are connected with H strips, and the joint is sealed with special sealant, which can effectively prevent water leakage of the awning.

6、用一種由鋁合金連接型材和密封墊，組成的裝配系統將板材固定;這樣遮陽篷就安裝完成了。

6. Fix the plate with an assembly system composed of aluminum alloy connecting profiles and sealing gaskets; This completes the installation of the sunshade.

為了您的家人的使用遮陽篷帶給您的快樂，請您在購買安裝遮陽篷的時候注意請專門的人員安裝!更多相關內容就來我們網站http://www.xilizx.com咨詢了解吧！

For your family to use the awning safely and bring you happiness, please pay attention to the special personnel when purchasing and installing the awning! Come to our website for more relevant content http://www.xilizx.com Ask about it!